Mikrotik Load Balancing 2 WAN 2 LAN RB1100AHx

Mikrotik Load Balancing 2 WAN 2 LAN with Failover – Load balance 2 WAN on Mikrotik Router is a technique to distribute the traffic load on the two-paths connection in a balanced manner, so that traffic can run optimally, maximize throughput, minimize response time and avoid overload on one connection path. This experiment, I have 2 internet connections different ip WAN and 2 LAN. I‘ve tried it, load balancing and failover can run normally. You can see the mikrotik script below.

Network Topology

IP WAN 1 = 10.10.10.2/29

IP WAN 2 = 10.10.11.2/29

Block IP LAN 1 = 192.168.1.0/24 Gatheway 192.168.1.1 Mask 255.255.255.0

Block IP LAN 2 = 192.168.100.0/24 Gatheway 192.168.100.254 Mask 255.255.255.0

1. Add Ip address to interfaces mikrotik router

Mikrotik Script :

/ip address
add address=10.10.11.2/29 interface=ether2 network=10.10.11.1
add address=10.10.10.2/29 interface=ether1 network=10.10.10.1
add address=192.168.1.1/24 interface=ether3 network=192.168.1.0

2. Setting IP Pool to restrict the range of IP that will distributed automatically by DHCP system thatwe enable.

Mikrotik Script :

/ip pool
add name=”LAN 1″ ranges=192.168.1.10-192.168.1.254
add name=”LAN 2″ ranges=192.168.100.20-192.168.100.30

3. Setting DHCP Server on mikrotik router

Mikrotik Script :

/ip dhcp-server
add address-pool=”LAN 1″ disabled=no interface=ether3 name=”staff”
add address-pool=”LAN 2″ disabled=no interface=ether6 name= manager

/ip dhcp-server network
add address=192.168.1.0/24 dns-server=8.8.8.8,8.8.4.4 gateway=192.168.1.1
add address=192.168.100.0/24 dns-server=8.8.8.8,8.8.4.4 gateway=192.168.100.254

4. Add the both private address (IP LAN) to the firewall address list

Mikrotik Script :

/ip firewall address-list
add address=192.168.1.0/24 list=”block lan”
add address=192.168.100.0/24 list=”block lan”

5. Setting Firewall NAT

Mikrotik Script :

add action=masquerade chain=srcnat out-interface=ether1 src-address-list=
“block lan” to-addresses=10.10.10.2
add action=masquerade chain=srcnat out-interface=ether2 src-address-list=\
“block lan” to-addresses=10.10.11.2

6. Setting Mangle

Mikrotik Script :

/ip firewall mangle
add action=mark-connection chain=input in-interface=ether1 \
new-connection-mark=ip10con passthrough=no
add action=mark-connection chain=input in-interface=ether2 \
new-connection-mark=ip11con passthrough=no
add action=mark-routing chain=output connection-mark=ip10con new-routing-mark=\
to-ip10 passthrough=no
add action=mark-routing chain=output connection-mark=ip11con \
new-routing-mark=to-ip11 passthrough=no

7. Setting IP Route

Mikrotik Script :

/ip route
add distance=1 gateway=10.10.10.1 routing-mark=to-ip10
add distance=1 gateway=10.10.11.1 routing-mark=to-ip11
add check-gateway=ping distance=1 gateway=10.10.10.1,10.10.10.1

Test Result

This is winbox capture of test result